Already a subscriber? 
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
ISO 5599-2:2001 Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector, 2001
- Pneumatic fluid power— Five-port directional control valves—
- Contents Page
- Foreword
- Introduction
- Pneumatic fluid power— Five-port directional control valves— [Go to Page]
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Dimensional requirements and tolerances [Go to Page]
- 4.1 Dimensional requirements for sizes1E, 2E and 3E are shown in Figure
- 4.2 Dimensional requirements for sizes4E, 5E and 6E are shown in Figure
- 4.3 The main dimensions and tolerances of form and location of the interface features are show...
- 4.4 Tolerances on surface condition, within the continuous lines, shall be as follows:
- 4.5 The mounting surface shall not include any orifices other than those shown in the figures....
- 5 Identification of ports and orifices [Go to Page]
- 5.1 The flow path orifices in the mounting surface interface, and the ports serving these orif...
- 5.2 For monostable valves, the mandatory stable position of the valve shall always be identica...
- 5.3 When a positive signal is applied to control mechanism12, flow port1 shall be connected ...
- 5.4 The orientation of control mechanisms12 and 14 on the valve relative to flow ports2, 3, ...
- 5.5 Additional options for port identification shall be in accordance with
- 6 Electrical connector [Go to Page]
- 6.1 General
- 6.2 Connector [Go to Page]
- 6.2.1 The connector shall be readily removable, if not required, and shall comply with the req...
- 6.2.2 Connectors shall be rated at
- 6.2.3 Connectors shall be rated at
- 6.2.4 Insulated leads shall be rated at
- 6.3 Contacts [Go to Page]
- 6.3.1 Each connector shall comprise four live contacts and one earth contact. The earth contac...
- 6.3.2 The pins shall have diameters of
- 6.3.3 Socket contacts shall have an opening that allows friction fits on the pin contacts.
- 6.4 Insulation [Go to Page]
- 6.4.1 Wire of a sectional area of from
- 6.4.2 Same-colour insulation on diagonally opposite leads shall be used.
- 6.4.3 Green insulation shall identify the earth connection.
- 6.5 Orientation [Go to Page]
- 6.5.1 The dimensions of the electrical connector shall conform to those given in Figure
- 6.5.2 The contacts shall be located at the corners of a rectangle, with the earth at the centre.
- 6.5.3 Contacts1 and 4 shall be oriented parallel to the valve port slots and towards the valv...
- 6.5.4 Contacts1 and 3 shall be used with single solenoid valves.
- 6.5.5 Contacts2 and 4 shall be used with the second solenoid of a double solenoid valve.
- 6.5.6 Contact5 shall be the earth ground.
- 6.5.7 Each connector half shall be kept in place when the valve body and base are disconnected.
- 7 Identification statement
- Bibliography [Go to Page]
