eLibrary >
ISO 6622-2:2013 Internal combustion engines - Piston rings - Part 2: Rectangular rings made of steel >
Expand All
TOC Search:
ISO 6622-2:2013 Internal combustion engines - Piston rings - Part 2: Rectangular rings made of steel, 2013
- Section sec_1
- Section sec_2
- Section sec_3
- Section sec_4
- Section sec_4.1
- Section sec_4.1.1
- Table tab_a
- Figure fig_1
- Section sec_4.1.2
- Section sec_4.2
- Section sec_4.2.1
- Table tab_b
- Figure fig_2
- Table tab_1
- Section sec_4.2.2
- Section sec_4.3
- Section sec_4.3.1
- Table tab_c
- Figure fig_3
- Table tab_2
- Section sec_4.3.2
- Section sec_4.4
- Section sec_4.4.1
- Table tab_d
- Figure fig_4
- Table tab_3
- Section sec_4.4.2
- Section sec_5
- Section sec_5.1
- Section sec_5.1.1
- Table tab_e
- Figure fig_5
- Section sec_5.1.2
- Section sec_5.1.2.1
- Table tab_f
- Figure fig_6
- Section sec_5.1.2.2
- Table tab_g
- Figure fig_7
- Section sec_5.2
- Section sec_5.2.1
- Table tab_h
- Figure fig_8
- Section sec_5.2.2
- Section sec_5.2.2.1
- Table tab_i
- Figure fig_9
- Section sec_5.2.2.2
- Table tab_j
- Figure fig_10
- Section sec_5.3
- Section sec_5.3.1
- Table tab_k
- Figure fig_11
- Section sec_5.3.2
- Section sec_5.3.2.1
- Table tab_l
- Figure fig_12
- Section sec_5.3.2.2
- Table tab_m
- Figure fig_13
- Section sec_5.4
- Section sec_5.4.1
- Section sec_5.4.1.1
- Table tab_n
- Figure fig_14
- Section sec_5.4.1.2
- Section sec_5.4.1.2.1
- Table tab_o
- Figure fig_15
- Section sec_5.4.1.2.2
- Table tab_p
- Figure fig_16
- Section sec_5.4.2
- Table tab_q
- Figure fig_17
- Table tab_4
- Section sec_5.5
- Figure fig_18
- Section sec_5.6
- Figure fig_19
- Table tab_5
- Table tab_6
- Section sec_5.7
- Figure fig_20
- Table tab_7
- Section sec_5.8
- Figure fig_21
- Table tab_8
- Table tab_9
- Section sec_5.9
- Figure fig_22
- Table tab_10
- Section sec_6
- Table tab_11
- Table tab_12
- Section sec_7
- Table tab_13
- Table tab_13___1
- Table tab_13___2
- Table tab_13___3
- Table tab_13___4
- Table tab_13___5
- Reference ref_1
- Reference ref_2
- Reference ref_3
- Reference ref_4
- Reference ref_5
- Reference ref_6
- Reference ref_7
- Reference ref_8
- Reference ref_9
- Reference ref_10
- Reference ref_11
- Reference ref_12
- Reference ref_13
- Reference ref_14
- Reference ref_15
- Reference ref_16
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Overview
- 4 Ring types and designation examples
- 4.1 Type R — Straight-faced rectangular ring
- 4.2 Type B — Barrel-faced rectangular ring
- 4.3 Type BA — Asymmetrical barrel-faced rectangular ring, h1 ≥ 1,2mm
- 4.4 Type M — Taper-faced rectangular ring
- 5 Common features
- 5.1 Type R — Straight-faced rectangular ring
- 5.2 Type B — Barrel-faced rectangular ring
- 5.3 Type BA — Asymmetrical barrel-faced rectangular ring, h1 ≥ 1,2 mm
- 5.4 Type M — Taper-faced rectangular ring
- 5.5 Type R, B, BA, and M rings (positive twist type) — Internal bevel top side
- 5.6 Type M rings (negative twist type), taper M3 to M5 — Internal bevel bottom side
- 5.7 Type R, B, BA, and M rings — Outside and inside rounded edges
- 5.8 Type R, B, BA, and M rings (fully faced and inlaid) — Plating/coating thickness
- 5.9 Type R, B, BA, and M rings — Nitrided case depth
- 6 Force factors
- 7 Dimensions and forces
- Bibliography [Go to Page]