eLibrary >
ISO/IEC 12862:2011 Information technology - 120 mm (8,54 Gbytes per side) and 80 mm (2,66 Gbytes per side) DVD recordable disk for dual layer (DVD-R for DL) >
Expand All
TOC Search:
ISO/IEC 12862:2011 Information technology - 120 mm (8,54 Gbytes per side) and 80 mm (2,66 Gbytes per side) DVD recordable disk for dual layer (DVD-R for DL), 2011
- Scope
- Conformance [Go to Page]
- Normative references
- Terms and definitions
- Conventions and notations [Go to Page]
- Abbreviated terms
- General description of a disk
- General requirement [Go to Page]
- Reference measurement devices [Go to Page]
- 10 Dimensional characteristics [Go to Page]
- Mechanical parameters [Go to Page]
- Optical parameters [Go to Page]
- Operational signals for recorded disk [Go to Page]
- Operational signals for the unrecorded disk [Go to Page]
- Data Format [Go to Page]
- Data Frames [Go to Page]
- Scrambled Frames
- ECC Block configuration
- Recording Frames
- Modulation
- Physical Sectors
- Suppress control of the d.c. component
- Linking scheme [Go to Page]
- General description of the Information Zone [Go to Page]
- Lead-in Zone, Middle Zone and Lead-out Zone [Go to Page]
- General description of the Unrecorded Zone [Go to Page]
- Pre-pit Data format [Go to Page]
- Data structure of R-Information Zone and ODTA [Go to Page]
- B.1 Principle of the measurement
- B.2 Measurements conditions
- B.3 Example of a measuring set-up
- C.1 Measuring method for the differential phase tracking err
- C.2 Measurement of Δt /T without time interval analyzer
- C.3 Calibration of Δt /T
- D.1 Calibration method
- D.2 Measuring method
- F.1 System diagram for jitter measurement
- F.2 Open loop transfer function for PLL
- F.3 Slicer
- F.4 Conditions for measurement
- F.5 Measurement
- I.1 Wobble signal (WOb)
- I.2 Wobble amplitude
- J.1 Condition of the summing amplifier in the measurement ci
- J.2 Condition of the differential amplifier in the measureme
- J.3 Output gain of the summing and the differential amplifie
- K.1 Location of NBCA and Lead-in Zone
- K.2 Writing form
- K.3 Modulation method
- K.4 NBCA-Code structure [Go to Page]
- K.5 NBCA Error Detection Code (EDCNBCA)
- K.6 NBCA Error Correction Code (ECCNBCA)
- K.7 NBCA-Sync-Byte (SBNBCA) and NBCA-Resync (RSNBCA)
- K.8 NBCA signal specifications [Go to Page]
- K.9 Logical format of information data
- L.1 Border Zone construction
- L.2 Border Zone Size
- L.3 Border Zone Information [Go to Page]
- L.4 Border-out and Reduced Border-out [Go to Page]
- M.1 Block diagram for measurement
- N.1 Construction with Format1 RMD
- N.2 Construction with Format4 RMD
- O.1 Recording order for disk testing
- P.1 Clearance to keep the Recording order
- P.2 Example of the clearance in the number of sectors (Infor
- Q.1 General
- Q.2 Anchor Point Re-mapping
- Q.3 Anchor Point Data in Border Zone
- Q.4 Border structure with Re-mapping
- R.1 Laser focusing method
- R.2 Interferometer method
- S.1 General
- S.2 Packaging [Go to Page]