Search book title
Filters:
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(366)
ACI
(651)
AECDAILY
(599)
AISC
(57)
ASA
(290)
ASCE
(1055)
ASHRAE
(738)
ASME
(2283)
ASSE
(117)
ASTM
(99009)
AWC
(58)
AWWA
(650)
BHMA
(137)
BICSI
(42)
BIFMA
(29)
BOMA
(20)
BSI
(102918)
CRSI
(18)
IAHSS
(1)
IAPMO
(397)
ICC
(328)
IEC
(10763)
IEEE
(7368)
IES
(266)
ISEA
(21)
ISO
(24376)
Joint Commission
(206)
Joint Commission Int.
(1)
NEMA
(1010)
NETA
(7)
NFPA
(1737)
TCNA
(26)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(128)
CO
(1)
CT
(4)
FL
(58)
ID
(5)
IL
(7)
IN
(1)
KY
(1)
LA
(2)
MI
(28)
MN
(27)
NC
(36)
NJ
(13)
NY
(71)
OH
(24)
OR
(27)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(7)
WA
(34)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    A334/A334M-04a(2016) Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service
    Edition: 2016
    $144.00
    Unlimited Users per year

Description of ASTM-A334/A334M 2016

ASTM A334/A334M-04a-Reapproved2016

Historical Standard: Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service




ASTM A334/A334M

Scope

1.1 This specification2 covers several grades of minimum-wall-thickness, seamless and welded, carbon and alloy-steel tubes intended for use at low temperatures. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties.

1.2 Supplementary Requirement S1 of an optional nature is provided. This shall apply only when specified by the purchaser.

Note 1: For tubing smaller than 1/2  in. [12.7 mm] in outside diameter, the elongation values given for strip specimens in Table 1 shall apply. Mechanical property requirements do not apply to tubing smaller than 1/8  in. [3.2 mm] in outside diameter and with a wall thickness under 0.015 in. [0.4 mm].

(A) For each reduction of 0.01 % carbon below 0.30 %, an increase of 0.05 % manganese above 1.06 % will be permitted to a maximum of 1.35 % manganese.

1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


Keywords


ICS Code

ICS Number Code 23.040.10 (Iron and steel pipes)


DOI: 10.1520/A0334_A0334M-04AR16



This book also exists in the following packages...

Year Publisher Title Annual Price
VAR
ASTM
 [+] $1,292.14 Buy
VAR
ASTM
 [+] $7,149.79 Buy
VAR
ASTM
 [+] $6,754.31 Buy
VAR
ASTM
 [+] $4,137.72 Buy

Subscription Information

MADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

Some features of MADCAD.com ASTM Standards Subscriptions are:

- Online access: With MADCAD.com’ s web based subscription service no downloads or installations are required. Access ASTM Standards from any browser on your computer, tablet or smart phone.

- Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.

 

For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

About ASTM

ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide.
GROUPS
X