|
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8633 2026ASTM D8633-26Active Standard: Standard Test Methods for Evaluating the Cross-Grain Compression Strength and Stiffness of Wood and Wood-Based ProductsASTM D8633Scope 1.1 These test methods cover standardized procedures for evaluating the cross-grain compression strength and stiffness of wood and wood-based products. 1.2 Two types of test methods are provided: fundamental and application methods. 1.2.1 Fundamental Test Methods—These test methods characterize the general cross-grain compression strength and stiffness of the material using specimens that are not necessarily of commercial size. The results from these tests are intended to serve as potential inputs for modeling and analysis. 1.2.2 Application Test Methods—These test methods are designed to develop test data that represent the cross-grain compression stress states encountered in service. This is achieved by testing specimens of commercial size for determining their cross-grain compression strength, and sometimes deformation, in either direct or indirect bearing conditions. 1.3 These test methods do not address the development of design values, analytical models for specific applications, or performance requirements, or combinations thereof. These aspects are expected to be covered by the product standards that reference these test methods. 1.4 These test methods are not intended to replace the related provisions of Specifications D7672 or D5055, which provide specific test guidance to be used when evaluating rim board or pre-fabricated wood I-joist products, respectively. 1.5 These test methods apply to situations where full support is provided for the product thickness. Situations with partial bearing for the product thickness are outside the scope of these test methods. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords bearing; buckling; compression; cross-grain; crushing; mechanical properties; perpendicular-to-grain; stiffness; strength; ICS Code ICS Number Code n/a DOI: 10.1520/D8633-26 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|